Canton Tanks breather dry sump catch recovery power steering expansion fill coolant cap




3987 First Street, Suite G, Livermore, CA 94551	PHONE: (925)292-5522
		FAX: (925)292-5524	E-MAIL: Sales@LivermorePerformance.com

Back

Home

Products

Brakes
Camera Mounts
Data Acquisition
Drivetrain
Engine
Lights
Lubricants
Miscellaneous
Plumbing
Safety
Steering Wheels
Suspension Components
Tanks
Timing
Tools
Wheel Spacers

Car Specific Products

Acura & Honda
BMW
Chevrolet Corvette
Ford, Lincoln, Mercury
Ford Mustang
General Motors
Infiniti & Nissan
Mazda
Mini
Porsche

Company Information

Contact & Information
Store Location / Map


Tanks		Model Specific Tanks
Breather Catch Tanks	Expansion Tanks	Chevrolet Corvette	GM
Catch Tanks	Dry Sump Tanks	Ford	Mini
Catch / Fill Tanks	Power Steering Reservoir Tanks	Ford Mustang

BREATHER CATCH TANKS Canton's Breather Catch Tanks can be used to vent an engine, a dry sump tank, a rear end, or in any other application where a breather catch tank is required. The side port is connected to the vent line and the bottom port is used as a drain, any vapor that condenses is caught in the bottom of the tank. The pleated breather keeps any contaminates from entering the system. Comes with a petcock, and a standard 1-3/8" breather, a stainless steel mounting clamp for panel mounting and a weld-on bracket which allows for roll bar mounting.
	#23-030 Plain Aluminum #23-030PC Silver powder coated finish
	Size:	3-1/4" dia., 11-1/4" high
	Tank:	7" Tall, 24 oz tank.
	Side Port:	3/8" N.P.T.
	Bottom Port:	3/8" N.P.T.
	EVAC System Breather Tank #23-031 Plain Aluminum #23-031PC Silver powder coated finish
	Size:	3-1/4" dia., 11-1/4" high
	Tank:	7" Tall, 24 oz tank.
	Side Port:	-12 AN.
	Bottom Port:	3/8" N.P.T.
	For vacuum pump applications
	Short Breather Tank #23-032 16 oz. Plain Aluminum #23-032PC Silver powder coated finish
	Size:	3-1/4" dia., 9-1/4" high
	Tank:	5" Tall, 16 oz tank.
	Side Port:	3/8" N.P.T.
	Bottom Port:	3/8" N.P.T.
	For applications with limited room
	#26-890 TANKS CLAMPS These Replacement Mounting Clamps are 3-1/4" in diameter and are made from stainless steel. These clamps can be used with the following tanks: #23-030, #23-031 and # 23-035

Breather Catch Tanks

P/N

Price

UNIV BREATHER TANK 3/8” SIDE PORT BOTTOM PETCOCK

23-030

$94

UNIV BREATHER TANK 3/8” SIDE PORT BOTTOM PETCOCK, 23-030 POWDER COATED

23-030PC

$108

UNIV BREATHER VENT TANK FOR EVAC SYSTEMS, -12 AN Side port and a 3/8" bottom outlet

23-031

$97

UNIV BREATHER VENT TANK FOR EVAC SYSTEMS, -12 AN Side port and a 3/8" bottom outlet, 23-031 POWDER COATED

23-031PC

$110

UNIV BREATHER VENT TANK 16 OZ, Short, 3/8" Side Port, 3/8" Bottom Petcock

23-032

$94

UNIV BREATHER VENT TANK 16 OZ, Short, 3/8" Side Port, 3/8" Bottom Petcock, 23-032 POWDER COATED

23-032PC

$108

CM UNIV CANISTER FILTER MOUNTING CLAMP, ROUND

26-890

Back

Livermore Performance (925)292-5522

Top of Page

CATCH TANKS Canton's universal overflow catch tanks can be used to capture any overflow of fluid. Many classes of racing require catch tanks to keep oil and coolant from discharging on to the race track. When used as catch tanks the side port is used as the input and the bottom port can be used as a drain and the top port as a vent. (petcock included) Designed to be both light weight and strong.
	#80-205 24 oz. Coolant Drag Race Overflow Catch Tank. This lightweight aluminum catch tank has a 3/8" fitting on the top for a vent tube which is essential for evacuating pressure. Also comes with a 3/8" N.P.T. side fitting and bottom petcock. Comes with a mounting clamp and a weld bracket which allows for panel or tube mount.
	Size:	3-1/4" Dia., 9" total height.
	Tank:	24 oz. tank.
	Top Vent Port:	3/8" N.P.T.
	Side Port:	3/8" N.P.T.
	Bottom Port:	3/8" N.P.T with petcock.
	Replacement clamps ( #26-890 )
	#80-250 Billet Coolant Overflow Catch Tank This billet aluminum tank can be used as either an overflow catch tank, or as a recirculating expansion tank. Lightweight compact design features removable screw in end caps with o-ring seals. Includes two 90° 5/1"6 barbed fittings, one straight 5/1"6 barbed fitting, a petcock drain plug, and a stainless steel mounting clamp. The tank is blue anodized with clear anodized end caps
	Size:	2-3/4" Dia., 9" total height.
	Tank:	24 oz. tank.
	Top Vent Port:	3/8" N.P.T.
	Bottom Port:	3/8" N.P.T with petcock.

Coolant Overflow Catch Tanks

P/N

Price

UNIV COOLANT DRAG RACE CATCH TANK 3/8”, 3/8” & PETCOCK

80-205

$83

BILLET ALUMINUM OVERFLOW CATCH TANK

80-250

$69

Back

Livermore Performance (925)292-5522

Top of Page

CATCH / FILL TANKS Canton's universal coolant recovery / catch tanks can be used on coolant recovery systems by connecting the radiator overflow into the bottom port. Any expansion of coolant will be pushed into the tank, and when used with a radiator with a recovery cap, will return to the radiator during cool down. Plumbed this way the tank can be used as a fill point and reservoir. These tanks can also be used as general catch tank to capture any discharging on the race track. When used as catch tanks the side port is used as the input and the bottom port can be used as a drain. (petcock and vented cap included) These tanks are both light weight and strong.
	#80-201 2qt Coolant Recovery/Fill Tank This versatile 2 Qt. aluminum tank features a vented fill cap, built in mounting tabs, and a clear tube sight gauge. Bottom and side ports allow this tank to be used as a recovery or an overflow catch tank. Includes two 5/16" barbed fittings (one straight, one 90°), one socket hex plug, and one petcock drain fitting.
	Size:	9-3/4" Tall, 7" Wide, 4" Deep.
	Tank:	2 qt. tank.
	Side Port:	1/4" N.P.T.
	Bottom Port:	1/4" N.P.T.
	vented cap included
	#80-206 Coolant Overflow Catch Tank with Vented Cap Comes with a mounting clamp and a weld on bracket which allows for panel or tube mounting.
	Size:	3-1/4" dia., 9" total height
	Tank:	24 oz tank.
	Side Port:	3/8" N.P.T.
	Bottom Port:	3/8" N.P.T. with petcock.
	Replacement clamps ( #26-890 )
	#80-211 4qt Coolant Recovery/Fill Tank This versatile 4 Qt. aluminum tank features a vented fill cap, built in mounting tabs, and a clear tube sight gauge. Bottom and side ports allow this tank to be used as a recovery or an overflow catch tank. Includes two 5/1"6 barbed fittings (one straight, one 90°), one socket hex plug, and one petcock drain fitting.
	Size:	10-1/4" Tall, 8-3/4" Wide, 4" Deep.
	Tank:
	Tank:	4 qt. tank.
	Side Port:	1/4" N.P.T.
	Bottom Port:	1/4" N.P.T.

Coolant Overflow Catch Tanks

P/N

Price

ALUM RECOVERY TANK 2 QT CAPACITY

80-201

$105

UNIV COOLANT OVERFLOW CATCH TANK W/ VENTED CAP

80-206

$98

ALUMINUM RECOVERY TANK 4 QT CAPACITY

80-211

$112

Back

Livermore Performance (925)292-5522

Top of Page

EXPANSION TANKS Canton expansion tanks are built with .100" thick aluminum and have billet aluminum necks with a barbed overflow fitting and accept standard radiator caps. Expansion tanks provide an air space for the coolant to expand into and are required in all applications where the top or the radiator is lower than the top of the engine. These tanks should be completely filled. The tank itself should only be partially filled to allow for expansion. Has built in mounting brackets. An overflow hose can be connected to the filler neck barbed fitting.
	#80-200 1 ¼ qt Coolant Recovery/Fill Tank This lightweight aluminum expansion fill tank has a ½" N.P.T. bottom fitting and a 3/8" N.P.T. side fitting. Has built in mounting radiator style cap. Recommended for applications where the top of the radiator is lower than the top of the engine. Mounting the tank higher than the engine insures a complete fill and provides an air space for expansion.
	Size:	5-1/2" Tall, 4-1/2" Wide, 3" Deep.
	Tank:	1-1/4 qt. tank.
	Side Port:	3/8" N.P.T.
	Bottom Port:
	Bottom Port:	1/2" N.P.T.
	Related parts,	#81-016 & 81-030 Expansion tank pressure caps.
EXPANSION TANK PRESSURE CAPS These pressure caps are for use with our aluminum expansion tanks or any other application that requires a high pressure radiator style cap. Two different pressure settings are available.
	#81-016 16 psi. Radiator Style Cap. #81-030 30 psi. Radiator Style Cap.

Multi-Use Coolant Expansion / Fill Tanks

P/N

Price

UNIV COOLANT EXPANSION/FILL TANK 1/2” N.P.T. Bottom Port, 3/8” N.P.T. Side Port, 1 ¼ qt. Capacity

80-200

$105

Model Specific Coolant Expansion / Fill Tanks

P/N

Price

Expansion Tank Pressure Caps

P/N

Price

EXPANSION TANK PRESSURE CAP 16 LBS

81-016

$10

EXPANSION TANK PRESSURE CAP 30 LBS

81-030

$26.33

Back

Livermore Performance (925)292-5522

Top of Page

DRY SUMP TANK & ACCESSORIES
	#23-110 DRY SUMP TANK This dry sump tank features three stage deaeration baffling, a spiral oil runner, and a integral mounting flange. It is equipped with a1-1/16" -16AN female oil entrance port, -12AN female oil exit port, and a1/4" N.P.T. drain and a 1/2" N.P.T. vent port. The tank is 77.5" wide by 67.5" deep by 147.5" tall and will hold up to 10 quarts of oil.
Dry Sump Breather / Catch Tank
	#23-036 Dry Sump Breather / Catch Tank This breather tank features a 1-3/8" pleated breather and internal baffling which allows excess pressure to be released from the dry sump tank and breather tank, while preventing oil from escaping out of the breather element. 24oz capacity.

External Oil Pump Pickup Kits Universal External Oil Pump Pickup Kits include a pickup cup welded to a 3/4" dia. 3-1/2" long tube, and a -12 AN fitting. This kit can be used to convert a standard wet sump pan to one used with an external oil pump or to add an extra pickup to a dry sump pan. Welding is required. NOTE: Canton will install these kits in any of Canton's wet sump oil pans on a special order bassis.
	#20-720 Steel screened pickup cup, tube, and fitting. #20-720A Aluminum non-screened pickup cup, tube, and fitting.
		Recommended or related parts. #22-660 In-line screen protector with -12 male fittings. #22-750 Screen dry sump protector with -12 male and -12 female fittings.
IN-LINE SCREEN PROTECTORS Canton's In-line Screen Protectors for dry sumps, external pump wet sumps, or rear end coolers. They protect your pump's inner workings from metal chips or debris without restricting the oil flow. We recommend their use on all scavenge (suction) lines. They can be easily disassembled for cleaning and inspection. Eliminates costly pump repairs.
	#22-640 In-line Screen Protector -8 AN Fittings. #22-650 In-line Screen Protector -10 AN Fittings. #22-660 In-line Screen Protector -12 AN Fittings. #22-680 Replacement Screen. #98-005 2 PK Replacement O-rings.
SCREEN DRY SUMP PROTECTOR Most high quality dry sump pans (such as ours) do not have screens on the scavenge tubes. It is not practical to have to remove the oil pan to check for debris. Canton's screen protectors should be installed on each scavenge fitting or in each scavenge line. This will prevent pump damage, and makes inspection and cleaning a lot less time consuming. Canton's Oil Pump Protector threads on to a -12 male AN oil pan fitting and accepts a -12 AN female hose end. Only extends the oil pan fitting a little over two inches so it can fit most applications. No restriction to oil flow but stops debris.
	#22-750 -12 AN Screen Pump Protector. #22-760 Replacement Screen.

DRY SUMP TANK

P/N

Price

DRY SUMP TANK RIGHT FITTINGS

23-110R

$240

DRY SUMP TANK LEFT FITTINGS

23-110L

$240

Dry Sump Breather / Catch Tank

DRY SUMP BREATHER CATCH TANK 24 OZ

23-036

$90

External Oil Pump Pickup Kits

UNIV EXTERNAL PICKUP KIT -12 AN WELDING REQ.

20-720

$30

UNIV EXTERNAL ALUM PICKUP KIT -12 AN WELDING REQ.

20-720A

$40

IN-LINE SCREEN PROTECTORS

UNIV IN-LINE SCREEN FILTER -8 AN MALE

22-640

$48

UNIV IN-LINE SCREEN FILTER -10 AN MALE

22-650

$48

UNIV IN-LINE SCREEN FILTER -12 AN MALE

22-660

$48

REPLACEMENT SCREEN FOR 22-650/660 IN-LINE FILTER

22-680

$12

O-RINGS FOR 23-000 SERIES PORT FITTINGS 2 PK

98-005

SCREEN DRY SUMP PROTECTOR

UNIV MINI IN-LINE SCREEN FILTER -12AN MALE/-12AN FEMALE

22-750

$30

REPLACEMENT SCREEN FOR 22-750 MINI IN-LINE FILTER

22-760

$11

Back

Livermore Performance (925)292-5522

Top of Page

POWER STEERING RESERVOIR TANKS Lightweight Aluminum Power Steering Tank for applications where a remote reservoir is used. Baffled for better fluid control.
	#77-250 POWER STEERING RESERVOIR TANK with female N.P.T. ports. Comes with a heavy duty stainless steel mounting clamp. Can be used with power steering reservoir tank fittings.
	Size:	3-1/4" Dia. by 7-3/8" total height, 23 oz tank.
	Side Return Port:
	Side Return Port:	3/8" N.P.T.
	Bottom Feed Port:	1/2" N.P.T.
	Recommended or related parts #26-890 Replacement clamps #77-212 Aluminum power steering pump and pulley.
	#77-252 POWER STEERING RESERVOIR TANK with male AN fittings. Comes with a heavy duty stainless steel mounting clamp.
	Size:	3-1/4" Dia. by 7-3/8" total height, 23 oz tank.
	Side Return Port:
	Side Return Port:	-6 AN.
	Bottom Feed Port:	-10 AN.
	Recommended or related parts #26-890 Replacement clamps
	#77-253 High capacity NASCAR style P/S tank.
	Size:	3-1/4" Dia. by 9-3/4" total height, 31 oz tank.
	Side Return Port:	-6 AN.
	Bottom Feed Port:
	Bottom Feed Port:	-10 AN.
	Recommended or related parts #26-890 Replacement clamps
Pump Mounted Power Steering Tank Canton's pump mounted power steering tanks are designed to replace the stock pump mounted plastic tanks. Built out of .100" aluminum these tanks provide a stronger more reliable better looking tank that eliminates the need for a remote tank. The tank features internal baffle and vented cap. Canton's pump mounted tanks are designed to work with pulleys designed for pump mounted tank applications. Tank is offered in two different feed fitting sizes to accommodate different pumps..
	#77-260 Designed with a straight .615 feed port to mount to #77-210 compact power steering pump. #77-261 Designed with a .75 stepped to a .615 feed port to mount to those power steering pump.